WIRE FORMING MACHINES – FOUR SLIDES

• #5 U.S. Baird 4-Slide, S/N 51-1440-46, w/ 1 Vert. Motion, Stock Check, Cutoff, Straightener,

Enclosed Gears, 5 H.P., Vari-Drive •

• #4 Nilson 4-Slide, S/N 43168, w/ 1 Vert. Motion, Stock Check, Cutoff, Straightener,

US Vari-Drive Motor, Enclosed Gears •

• #4 Nilson 4-Slide, S/N 74200, 1 Vert. Motion, Double Feed Mach., w/ Weldtronic Welder,

Enclosed Gears, (2) Straighteners, Motor & Controls •

• #4 Nilson 4-Slide, S/N 86790, 1 Vert. Motion, Double Feed Mach., w/ Weldtronic Welder,

Enclosed Gears, (2) Straighteners, Motor & Controls •

• #4 Nilson 4-Slide, S/N 69810, 1 Vert. Motion, Double Feed Mach., w/ Weldtronic Welder,

Enclosed Gears, (2) Straighteners, Motor & Controls •

• S-3-F Nilson 4-Slide, S/N S-3-F-13067, Stock Check, Cutoff, Press Head, 1 Vert. Motion,

Straightener, Clarktron Rimfire 3 Controls, Enclosed Gears, 3 H.P., 220/440/3/60 •

• #3 U.S. Baird 4-Slide, Stock Check, Cutoff, 1 Vert. Motion, Straightener, Open Gears,

Motor & Controls •

• S-1-F Nilson 4-Slide, S/N 69100, Stock Check, Press Head, Enclosed Gears, Cutoff,

Straightener, Vari-Drive Motor, 2 Vert. Motions •

• S-1-F Nilson 4-Slide, S/N 68600, Air Clutch, Enclosed Gears, Stock Check, Cutoff,

Straightener, 1 Vert. Motion, Press Head w/ Tie Rods •

• S-2-F Nilson 4-Slide, S/N 64840, Stock Check, Cutoff, Straightener, 2 Vert. Motions,

Enclosed Gears, US Vari-Drive •

• #752 Nilson 4-Slide, S/N 89752, Elec. Clutch, 1 Vert. Motion, Stock Check,

2 Press Heads w/ Tie Rods, Cutoff, Straightener, Reeves Vari-Drive •

• #752 Nilson 4-Slide, S/N 90652, Elec. Clutch, 1 Vert. Motion, 2 Press Heads w/ Tie Rods,

Straightener, Reeves Vari-Drive •

• (2) #2 Size Homemade Dbl. Feed 4-Slides, 2 Vert. Motions, Robotran Welders on Common Base,

Vari-Drive Motors •

WIRE FORMING MACHINES – MULTI SLIDES

• #33 U.S. Tool Symmetrical Multi Slide, S/N 33-393 Kingpost, 2 Press Heads,

Front & Rear Cutoffs, Straightener, 1 Support, 2 Bolsters, Enclosed Gears,

5 H.P. Vari-Drive, Gordon Proxagard •

• #33 U.S. Tool Symmetrical Multi Slide, S/N 33-332, Kingpost, 2 Press Heads, 1 Bolster,

Stock Check, Straightener, Clarktron Controls, Vari-Speed, Front & Rear Cutoffs •

• #33 U.S. Tool Symmetrical Multi Slide, Kingpost, 2 Press Heads, Front & Rear Cutoffs,

1 Bolster, Straightener, Gordon Proxagard, U.S. Vari-Drive Motor •

• #33 U.S. Tool Symmetrical Multi Slide, S/N 33-528, Kingpost, Front & Rear Stock Checks

& Cutoffs, 1 Press Head, Straightener, Gordon Proxagard, Vari-Drive Motor •

• #33 U.S. Tool Symmetrical Multi Slide, S/N 33-447, Front & Rear Stock Checks & Cutoffs,

1 Press Head w/ Bolster, Straightener, (1) Motoren Threading Head, (2) Weber Drill Heads •

• #33 U.S. Tool Symmetrical Multi Slide, S/N 33-561, Front & Rear Stock Checks & Cutoffs,

1 Press Head, Straightener, (1) Motoren Air Head, (3) Weber Pneu. Drill Heads,

Vari-Drive Motor •

• #33 U.S. Tool Non-Symmetrical Multi Slide, S/N 53-84281, Air Clutch, Kingpost,

Front Stock Check, 1 Press Head & 1 Bolster, Front & Rear Cutoffs, Straightener,

(2) ARO Air Tapping Heads, (1) Overarm Support, Vari-Drive Motor •

• #28 U.S. Tool Symmetrical Multi Slide, S/N 28-532, Kingpost, Front Stock Check, 1 Press Head,

1 Bolster, Rear Cutoff, Straightener, Clarktron Rimfire 3 Safety, Vari-Drive Motor •

• #28 U.S. Baird Symmetrical Multi Slide, S/N 28-855, Air Clutch, Kingpost,

Front & Rear Stock Checks & Cutoffs, 1 Press Head, 1 Bolster, Straightener,

Clarktron Rimfire 3 Safety, Vari-Drive Motor •

Note: All Multi Slides have Enclosed Gears, Split Cams & Split Cams w/ Inserts!

• Large Qty. of Split Cams, Slides, Kingpost, Overarm Supports, Bolsters, Press Heads, Lifter Arms, Straighteners, 2-Plain, Flat Stock, Formlifter's, Etc., for Multi Slides & Four Slides •

VERTISLIDE WIRE FORMERS

• OMCG Vertical Auto. Threading & Bending Mach. #M29, S/N 22057 w/ Straightener, Split &

Insert Cams Control Console, 24” Feed, 0.315 Max Wire Dia: Vari-Sp. w/ Threading Attach., 7.5 KW (1987 Mint) •

• Torrington V-82 Vertislide, S/N 114383FS, Strip Width: 2.5” Max; Strip Thickness: .062” Max; Wire

            Size: .027” Max; Feed Length: 12” Max; 40-200 PPM, w/ 2 Press Heads, 1 Bolster, Overarm 

            Support, Stock Check, Cutoff, ARO Lead Screw Vert. Mounted Tapper, Straightener, Control 

Console, Elec. Safety Bar, Motorized Conveyor, Split Cams •

• Rheinische Maschine Fabrik Vertislide, Type DBA 4/500, S/N 4104918, 4KW Motor, 0-300 PPM,

Vari-Drive, (5) Vert. Slides, (2) Horiz. Slides, (2) 45° Cutoff Slides, Straightener,

Push Button Controls, Approx. 3/16” Wire Dia. •

THREAD ROLLERS

• #4-600 Hartford Thread Roller, 0-600 RPM, Coolant, Push Button Controls, 7.5 H.P.,

Vari-Drive, Air Controls (Rebuilt 1995) •

• #10-400 Hartford Thread Roller, S/N 35-356/6, Auto Lube, 15 H.P., Vari-Drive,

Push Button Controls •

• Hartford Horizontal #312M Thread Roller, S/N 179-32, Vari-Sp. Motor,

Push Button Controls, Coolant •

• Hartford #0-400R, S/N 4-544-37, Vari-Sp., Auto Lube, Coolant •

• #30 Waterbury Farrell Inclined Thread Roller, S/N 33979-463, Auto Lube, 20 H.P. Motor •

• #20 Waterbury Inclined Thread Roller, S/N 5-188, 10 H.P., Auto Lube, Vibratory Feeder •

• #10 Waterbury Farrell Rotary Die Threader, S/N 171780-11, Max Cap: ¼” Dia.; Min Cap:

6 Size Screw; Max Screw Length: 2”; Max Thread Length: 2”; Vari-Sp. Drive •

• #10 Waterbury Farrell Inclined Thread Roller Parts Machines, Motor & Controls •

• Warren Threader, M/N WT-1000, S/N 128310-5, Vari-Sp., Pendant Controls •

SCREW SLOTTERS

• Illinois Tool Works, M/N 3220-3 Screw Slotter, S/N 8708, Vari-Sp., Vibratory Parts Feeder •

• Warren Screw Slotter, M/N WS-500, S/N 127790, Vari Saw & Hopper Controls, w/ Vibratory Bowl •

HEADERS

• National 3/16” Header, S/N 36662, 7.5 H.P., Auto Lube, Push Button Controls •

• National 3/16” Header, S/N 36204, 7.5 H.P., Auto Lube, Push Button Controls •

• National #25HS Dbl. Stroke Solid Die Header, S/N 41070, 5 H.P., Auto Lube, Push Button Controls •

• National #25HS Dbl. Stroke Solid Die Header, S/N 30470, 5 H.P., Auto Lube •

• (2) Hartford 1/8” Dbl. Stroke Solid Die Cold Headers, M/N 2-450, S/N’s 5200-165-9 & 5200-157-9,

7.5 H.P., Control Panel w/ Straighteners •

• #0 1/8” Waterbury Farrell S.S.D. Die Header S/N 86534-750; ¾ H.P. Synchogear Drive Motor,

Straightener, Push Button Controls •

RIVETERS

• (7) Milford #LDD Horizontal Riveting Machines, Vari-Drive Motors, (3) w/ Vibratory Feeds •

• Milford Vert. Air Operated Rivet Machine, w/ Adj. Anvil •

• Milford Vert. Foot Operated Rivet Machine, Adj. Arm Height •

SHAVERS

• (4) Townsend #2 Shavers, ½” Blank Dia., 3” Blank Length, w/ Vibratory Bowl,

A/C Motor & Controls •

AUTOMATIC SCREW MACHINES

• Brown & Sharp  #2G Automatic Screw Mach., 1¼” Cap, S/N 12474, Double Chain Drive,

Front & Rear Tool Posts, 1 Vert. Slide w/ Feed & Change Gears •

• (2) Brown & Sharp #OOG Auto Screw Machines, ¾” Cap, S/N 16365 & 16363 Dbl. Belt Machines

w/ Bar Feed, Vert. Slide, Front & Rear Tool Posts & Gears •

• (4) Traub A25 Swiss Screw Machines •

EDM MACHINES

• Mitsubishi DWC90SB Wire EDM, S/N 029SB331, w/ Mitsubishi Control & CRT w/ Tank, Filters,

Cooler, w/ Greed Mini File Plus – SS2 Transformer, Pendant Controller, Leveling Pads; 9.5”X, 11.5”Y, 6.5”Z Axis (New 1992) •

• Pratt & Whitney Fanuc Tape Cut-W-3 Wire EDM, S/N 8179 w/ Fanuc Type A04B –0246-B003,

Control w/ CRT (1989) w/ Tank, Cooler, Spool Pan, U-V Axis Head, Fanuc Pendant Controller,

            Misc. Accessories, Manuals, Leveling Pads: 29.5”X; 13.8”Y; 9.85”Z Axis Travels •

• New EDM Wire Spools, Tooling, Resin Tanks, Filters, Etc. •

DRILL

• Clausing 20” H.D. Floor Drill, Vari-Sp., M/N 2277, S/N 528083, 18” x 16” Table,

6” Quill Travel 3MT, 150-2000 RPM, 1½/ .75 H.P., 460V •

COMPARATORS

• Jones & Lamson 14” Optical Comparator, FC-14, S/N F15759, Novalite Projector,

Surface Illumination, Power Elevation, 20X Lense, 6” x 30” Table, 115V, 1 Ph., 60 HZ •

• Clausing Covel 14” Optical Comparator, M/N 4304, S/N 14B-4037, 6” x 13” Table w/ Lense, 115V •

• Lertz Watzler 19½” x 19½” Optical Comparator, S/N 836225, 10X Lense, 115V •

SURFACE GRINDERS

• Parker Majestic 6” x 18” Hand Feed Surface Grinder, S/N SCV-2672-71, 1 H.P., w/ Power Elev. •

• Norton 8” x 24” Hyd. Surface Grinder, 2 Axis, S/N 811, w/ 8” x 24” Perm. Mag. Chuck,

Coolant & Pump, 230/460V, 2 H.P. •

• DoAll 6” x 18”, 2-Axis Hyd. Surface Grinder, #G-1, S/N GI-51864, 1 H.P. •

• (2) Brown & Sharp 618 Micromaster 2 Axis Hyd. Surface Grinders

w/ 6” x 18” Perm. Mag. Chucks, S/N’s 523-181-5895 & 523-6181-2286 •

• Boyer Schultz H612 Challenger Hand Feed Grinder, S/N 22456, Elec. Lube,

6” x 12” Perm. Mag. Chuck, 1 H.P., 1 Shot Lube •

• Reid-Rollerway 6” x 18” Precision Hand Feed Surface Grinder, S/N 17818,

6” x 18” Perm. Mag. Chuck, 1 H.P., 1 Shot Lube •

• DoAll 2 Axis Hyd. Surface Grinder 6” x 18”, M/N G618-7, S/N 213-70615, 1 H.P.,

Auto Lube, 618 Fine Line P.M. Chuck •

• Clausing Covel 6” x 12” Hand Surface Grinder, M/N 7B, S/N 7B-7331,

6” x 12” Perm. Mag. Chuck, 1 H.P. •

MISCELLANEOUS GRINDERS

• Hamco Machines #B Blade Grinder, S/N 1021, 115V •

• Hammond 6” #600-W Abrasive Belt Grinder, S/N 1339, ½ H.P., 230V w/ Tilt Table •

• Wiley Tool 6” S.E. Diamond Wheel Grinder w/ Tilt Table, 1/8 H.P., 220V •

• Rockwell 6” Double End Carbide Grinder, ½ H.P., 1 Ph., #23-506, Tilt Tables, Fwd/Rev •

• Baldor 6” H.D. Half Bearing Double End Grinder, Cat #T12, S/N F978, 115V, ½ H.P. •

• Stanley 8” Double End Grinder #288A, ¾ H.P., 3 Ph., 220V, Tilt Table •

• Porter Cable 6” Vert. Belt Grinder, 1 H.P., 220V, Tilt Table •

• Setco Type 10SBAP, M/N 100, Double End Buffer, 1 H.P., 220/3/60 •

• Rockwell Combo 12” Disc & 6” Belt Grinder #31-710, 220/440/3/60 Motor •

• Solid 8” Double End H.D. Grinder, Type DS3GD, S/N 101408,

w/ Sliding Tables & Micrometer Dials, Coolant •

• Wilton #4200 Combo 12” Disc & 6” Belt Sander, 115V •

CENTERLESS GRINDERS

• Cincinnati #1 Centerless Grinder, S/N 1M4H5F-17, Hyd. Horiz. & Vert. Dressers,

4” Wide Wheels w/ Auto. Cycle Selector, Work Lite, 220V •

• Cincinnati #2 Centerless Grinder, S/N 2M2H2T-66, Hyd. Dressers, Work Lite •

• Cincinnati #2 Centerless Grinder, S/N 2M2H1V-12, Hyd. Dressers,

w/ Auto Thru Feed, Cycle Controls, 480V, Work Lite •

• Good Qty. Ass’t. New Grinding Wheels, Blades, Wheel Balancers,

Wrenches & Centerless Grinder Manuals•

INTERNAL GRINDER

• Overbeck #ZETTO30, S/N 1646, Internal Grinder, 45°, Swivel Work Head Motorized w/ 6 Jaw

Chuck, Hi-Speed Internal Grinding Head, Hand Feed, Push Button Controls, 220V/3/60 •

CYLINDRICAL GRINDERS

• Cincinnati R-58 Plain Hyd. Cylindrical Grinder, 10” x 16” CC, S/N 27542, Motorized Work Head,

12” Grinding Wheel, 56-500 RPM, Auto In-Feed, Spring Loaded Tool Stock, Misc. Tooling,

Coolant, Work Lite, 2-240 RPM, Traverse Speed •

• Grenby Cylindrical Grinder, ½ H.P. Grinding Head, Motorized Work Head, Coolant •

HONE MACHINES

• Superior SS-2 Horiz. Hone, S/N S-93-8605, Spdl. Speeds: 220-1750 RPM;

Dia. At 150 FPM 11/32” – 3” w/ Coolant, 115V, 1 Ph., 60 Hz. •

• Sunnen #MBB-1600-MS Horiz. Hone, S/N 41804, ½ H.P., 220/440/3/60 Motor •

• Good Qty. Sunnen & Superior Hone Tooling •

LATHES

• South Bend 17” x 40” Gear Head Lathe, #400, S/N 020375, 5 Sp., 59-1400 RPM, 2 1/8” Spdl. Hole,

Inch & Metric Threading, 8 Position Stops, Steady Rest, Thread Dial, Foot Brake Pedal,

D-1-6 Camlock Spdl, Positive Stops, Splash Guard Coolant, Work Lite,

Hand Lever 5C Drawbar, Leveling Pads, 10”- 3 Jaw Chuck w/ Key, 460V, 3/60 HZ •

• Hardinge 11” x 18” Precision Tool Room Lathe, HLV-H, S/N HLV-H-9042-1, Spdl Speeds, 125-

3000 RPM, Push Button Control, Coolant, 6¾” Wide Dovetail Bed Brake, 1½ H.P., 230V/3/60 •

• Hardinge HC Chucker, S/N HC-4929-7, Spdl. Speeds: 125-3000 RPM, Brake, 3 Speed Ranges,

5C Quirk Acting Collet Closer, 8 Position Stop, 8 Position Turret, Motorized Carriage,

Splash Guard, Work Lite, 6¾” Wide Dovetail Bed, Coolant, 1.5 H.P., 230V •

• Hardinge DV-59 Secondary Lathe, S/N 59-8243, Quick Acting 5C Collet Closer, Dovetail Bed,

Spdl. Speeds, 230-3500 RPM, Push Button Control, Tailstock, Splash Guard, Work Lite,

1 H.P., 440V •

• Hardinge DV-59 Secondary Lathe, Lever Actuated Hi-Low Speeds, 5C Quick Acting Collet Closer,

Dovetail Bed, Brake Work Lite, 1 H.P., 220V, w/ 6 Position Turret, S/N DV59-1690-1 •

• Hardinge DV-59 Secondary Turret Lathe, 6 Position Turret, 230-3500 RPM Spdl. Speeds, Push

Button Operated, 5C Quick Collet Closer Brake, Dovetail Bed, S/N DV-59-9052 •

• Hardinge DV-59 Secondary Lathe, w/ Tailstock, Spdl. Speeds: 230-3500 RPM, Push Button

Operated, 5C Quick Acting Collet Closer, Dovetail Bed, Brake, Work Lite, 1 H.P., 220V,

S/N 59-4980-3 •

• Feeler (Hardinge Type) Secondary Lathe, S/N 8FST07, M/N FTS-27, Spdl Speeds: 230-3500

RPM, 5C Quick Acting Collet Closer, Dovetail Bed, Coolant, Work Lite, ½ H.P., 220V •

• Hardinge HSL-5C Speed Lathe, S/N HSL-5C-4213, 5C Quick Acting Collet Closer, Dovetail Bed,

3 Spdl. Speeds, 750-300 RPM, ½ H.P., 220/440/3/60 Motor •

• South Bend 10” x 24” CC, Model A Bench Top Lathe, S/N BK200NKG, Cat# CL670Z, 3½’ Bed

Length, Belt Change, Threading, Fwd & Rev, 6K Collet Hand Wheel Collet Closer, Tool Post,

Work Lite, 220/440/3/60 HZ •

• Warner & Swasey 2MC Universal Turret Lathe, S/N 2478330, Lot 5, M/N 2650, Spdl. Speeds: 50-

3000 RPM, 12 Feeds, Coolant, Brake Bar Feed & Stands, Rear Tool Post, 4 Way Tool Post,

6 Position Turret, Work Lite, Hyd. Collet Closer, 220V/3/60 HZ •

• (2) Schauer Bench Top Speed Lathes, Type: NAIEL, Fwd. & Rev., 220V •

SAWS

• DoAll 16” Vertical Bandsaw, S/N 79-58187 w/ Welder, Grinder, Cutoff Attach., 2 Sp. 50-5200 RPM •

• Everett Hand Cutoff Saw, 8” Dia. w/ Vise, 3 H.P., 220/440/3/60, w/ Built on Dust Collector •

• Everett Cutoff Saw, 8” Wheel Vise, 3 H.P., 220/440V •

MILLING MACHINES

• Bridgeport Series II Special Vert. Miller, S/N 6818S, 11” x 58” Table, BPT. Power Feed,

Chrome Ways, Air or Manual Operated Knee, 2 H.P., 230/460/3/60 Vari-Sp. Head,

60-4200 RPM Spdl. Speeds, 2 Work Lites, 1 Shot Lube •

• Bridgeport Series I Vert. Miller, S/N 213568, Chrome Ways, 9” x 42” Table, 2 H.P., 230/460/3/60,

Spdl. Speeds: 60-4200 RPM, Work Lite, 1 Shot Lube •

• Bridgeport J-Head Vert. Miller, S/N 239834, 9” x 42” Table, Chrome Ways, 1 H.P., 230/460/3, 1

Shot Lube, 2 Work Lites •

• Bridgeport J-Head Vert. Miller, S/N 91218, 9” x 36” Table, #150 Servo Power Feed, Chrome Ways,

2 Work Lites, Teledyne Gurley Pathfinder 50, 2 Axis Dig. Readout •

• Supermax #YC-1½ VS Vert. Miller, 9” x 42” Table, Spdl. Speeds: 60-4200 RPM, Chrome Ways,

Work Lite, 2 H.P., 220/440/3/60 w/ Mitutoyo ADS-2, 2 Axis DRO •

PRESSES

• Bliss 60 Ton Air Clutch Obi Press, S/N H39549, 3” Stroke, 30” x 19½” Bed, 2 Bolster Plates,

2” x 2½” Dual Counter Balances w/ Stand Alone Control Console, Gordon Proxagard Safety,

Auto. Lube, 7.5 H.P. Vari-Sp. Motor •

• Perkins 45 Ton Obi Press, #550-B, 3” Stroke, 16” S.D.A.U. to Bed, A/C Motor & Controls •

• Manville Arch Frame Power Press, A/C Motor & Controls w/ Feed •

• 5 Ton Dbl. Action Obi Press w/ Parts Feeder •

• Denison 15 Ton Hyd. C-Frame Press, 15 H.P. •

• Rouselle 5 Ton #1A Obi Press, Jog/Run Controls, S/N BA8333, ¾ H.P., 220V •

• #3 Greenard Arbor Press • #2 Greenard Arbor Press •

• Air Hydraulics C-400 Hyd. 4 Ton Press, M/N C400, S/N 4120 •

HEAD LABELING & PACKING MACHINES

• (2) Bodolay/Pratt C-50 Head Label & Packing Machines, M/N C50HL, S/N 640; S/N 639, 440V,

1 Ph., w/ Whizlifter Packager & Golden Eagle, Scale, Hopper, Feed & Drain Unit

w/ Micro Scan, Solid State Controls, w/ Ass’t. Scales & Conveyors •

• Bodolay/Pratt Head Labeler w/ Conveyors, M/N C50HL, S/N 641, 440/1/60V •

• Bodolay/Pratt Head Labeler #C-50 w/ Conveyor, S/N 653, 440/1/60V •

• Arpac 1S12-50 Shrink Wrapper w/ Conveyors, S/N 1471, 100°-600° F, 208/3/60V •

• (4) Durable Packaging Heat Sealers, #RM-32, S/N 112583; #RM-42, S/N 022784;

#RM-34, S/N 029884; #RM-32, S/N 022984 •

PLANT SUPPORT EQUIPMENT

• (2) U.S. Tool 48” Dia., 2000# Motorized Horiz. Payoffs •

• U.S. Baird 48” Dia., 2000# Motorized Horiz. Payoff •

• (2) Rotarian Horiz. 500# Motorized Payoffs, 36” Dia. •

• (2) Coilmate PressPal 36” Dia., Motorized, 3500# Payoffs •

• Dbl. End 1000# ea. End Non-Motorized Payoff •

• Horiz. Light Duty Manual Reel • 40” Dia. Horiz. 500# Payoff Reel •

• Jaco JVRE-510-10 Motorized Vert. Payoff Reel • (2) Hi-Speed Key Weigh Programmable Units •

• Harshaw Elec. Spin Dryer • Torit #75 Dust Collector • Cincinnati Dust Collector •

• Pennsylvania Floor Scale w/ DRO • Toledo Dig. Bench Scale • Accu. Count & Weigh Scale •

• Large Asst. Vibratory Bowls, All Sizes 25+ •

• Large Qty. H.D. Metal Pallet Racking; Light Duty Racking; 2D Stor. Cabinets; Bench Weigh

Scales; Tape Shooters; Fireproof Cabinet & Containers; Benches; Sprayliner; H.D. Tote Bins; Portable  Carts; Various Size Scrap Hoppers & Conveyors; Hercules Dumpers; Lifts; Floor Mats; Overhead Lights; Oilers; Pneu. Cylinders; Die Carts; Motors; Seals; Valves; ARO Lead Screw Tappers; Arrow 3516 Compressor Dryer; Bodine Special Mach. Frame (New) •

• Approx. 100+ Press Dies •

• Lucifer HDL-8012-2 Furnace, 2300° F •

• Leeds Northrup Homo Furnace, 1400° F w/ Pots & Controls •

• Federal BAP-38, 15 KVA Spot Welder, Air Press Type, 220V •

• Cement Barrel Type Tumbler, Vari-Drive •

• Ass’t Electric Riding & Walk-Behind Forklifts •

MACHINE TOOL ACCESSORIES

• Kurt & Bridgeport Milling Vises • R-8, 5C Hardinge Collets • Lathe Chucks • Collet Closers •

• Collet Trays • Drill Chucks • 6K Collects • B&S #22 Collets • Hardinge #10, 15, 21, 22 Collets •

• Troyke 12” Rotary Table • Cincinnati Dividing Head • Gd Qty. Feed Finger •

• Geometric Die Head Dies • Bench Vises • Hardinge Bronze Bushing Pads • Gd Qty. Drills •

• 5/8 & 1” Shank Turret Tooling • Milford Rivet Tooling • Hardinge Compound • Tool Posts • V-Belts •

• Chuck Keys • Flat Belts • Strapping Tools • Screw Machine Cams & Access. •

• Many More Items too Numerous to Mention • Many of the Above Items New •

WASHER-DRYER

• (6) Jensen Jen-Fab #10186 S.S. Rotary Drum  Parts Washers w/ Exhaust & Temp. Controls •

• Jensen Jen-Fab 3-Stage Washer/Dryer, Water Sys., Auto./Man, M/N 9387, 230V,